The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.
Solar N Sat have a dedicated team of professional technicians with 13+ years in the industry!
The All-In-One Solar Power Solution: The Victron EasySolar-II GX integrates the following elements: • A MultiPlus-II inverter/charger • A SmartSolar MPPT -Tr solar charge controller • A GX device with a 2 x 16 character display. These elements come prewired together inside a single unit. This greatly simplifies most installations, saving time and money.
Display and Wifi: The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other wifi enabled device. In addition, wifi can be used to set up the system and to change settings
Solar Charge Controller: The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the MultiPlus-II inverter/charger. The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
GX Device: The integrated GX device includes: • A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g. VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use with a compatible CAN-bus Li-ion Battery • A USB port • A Ethernet port • A VE.Direct port The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a VE.Bus and a VE.Direct connection.
Grid In-Line Topology: The EasySolar-II GX will use excess PV power to charge the batteries or to feed power back into the grid and will discharge the battery or use power from the grid to supplement a shortage of PV power. In case of a power outage, the EasySolar-II GX will disconnect the grid and continue to supply the loads. Loads that should shut down when AC input power is not available can be connected to a second output. These loads will be taken into account by the PowerControl and PowerAssist function in order to limit AC input current to a safe value.
Grid Parallel Topology: The EasySolar-II GX will use data from the external AC current sensor (must be ordered separately) or power meter to optimise self-consumption and, if required, to prevent grid feed. In case of a power outage, the EasySolar-II GX will continue to supply the critical loads
PowerControl & PowerAssist: Yes Transfer Switch: 32A Maximum AC Input Current: 32A Auxiliary Output: Yes (32A)
Input Voltage Range: 38 – 66V Output Voltage: 230 VAC ± 2% Frequency: 50 Hz ± 0,1% (1) Cont. output power at 25°C (3): 3000VA / 2400W Cont. output power at 40°C / 65°C: 2200W / 1700W Maximum Apparent Feed-In Power: 2500VA Peak Power: 5500W Maximum Efficiency: 95% Zero Load Power: 11W Zero Load Power in AES Mode: 7W Zero Load Power in Search Mode: 2W
AC Input Voltage Range: 187-265VAC AC Input Frequency: 45 – 65 Hz Charge Voltage 'Absorption': 57,6V Charge Voltage 'Float': 55,2V Storage Mode: 52,8V Maximum Battery Charge Current (4): 35A Battery Temperature Sensor: Yes Programmable Relay (5): Yes Protection (2): a - g VE.Bus Communication Port: For parallel and three phase operation, remote monitoring and system integration General Purpose Com. Port: Yes, 2x
SOLAR CHARGE CONTROLLER
Model: SmartSolar MPPT 250/70-Tr Maximum Output Current: 70A Maximum PV Power: 4000W Maximum PV Open Circuit Voltage: 250V Maximum Efficiency: 98% Self-Consumption: 20mA Charge Voltage 'Absorption', Default: 57,6V Charge Voltage 'Float', Default Setting: 55,2V Protection (2): a – e
(1) Can be adjusted to 60 Hz (2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) 230 VAC on inverter output g) input voltage ripple too high (3) Non-linear load, crest factor 3:1 (4) At 25°C ambient (5) Programmable relay which can be set for general alarm, DC under voltage or genset start/stop function. AC rating: 230